Grout for ceramic tiles


Sienna 5Kg - 350166 20Kg - 350221
White 5Kg - 350167 20Kg - 350168
Chocolate 5Kg - 350170 20Kg - 350224
Black 5Kg - 350171 20Kg - 350187
Red 5Kg - 350172 20Kg - 350216
Graphite 5Kg - 350173 20Kg - 350189
Pearl 5Kg - 350174 20Kg - 350175
Cotton 5Kg - 350176 20Kg - 350214
Brown 5Kg - 350177 20Kg - 350223
Anthracite 5Kg - 350199 20Kg - 350210
Silver 5Kg - 350200 20Kg - 350211
Ivory 5Kg - 350201 20Kg - 350212
Ash 5Kg - 350202 20Kg - 350213
Salmon 5Kg - 350203 20Kg - 350215
Orange 5Kg - 350204 20Kg - 350217
Mint green 5Kg - 350205 20Kg - 350218
Blue 5Kg - 350206 20Kg - 350219
Pergamon 5Kg - 350207 20Kg - 350220
Cinnamon 5Kg - 350208 20Kg - 350222
Coffee 5Kg - 350209 20Kg - 350225
ARJUNT UNIVERSAL is a coloured modified polymer mortar based on hydraulic binders, resins and additives, as well as incorporating a broad-spectrum biocide agent that gives the product the necessary algaecide and fungicide capacity for use in contact with water and damp areas.

Installation video


Descriptive Memory

The grouting of the ceramic material, marble or natural stone will be carried out with ARJUNT® UNIVERSAL anti-fungus grout, from the company DANOSA, class CG2 AW according to UNE EN 13888. The substrate must be sound, clean, free of friable parts, completely hardened and have completed its time of dimensional variation.


  • Applicable on paving and walls.
  • Indoor and outdoor.
  • Grouting material for joint fillings from 1 to 20 mm wide in all types of ceramic tiles, stone materials, vitreous mosaic, marble, etc.
  • Damp areas.

Advantages & Benefits

  • Algaecide and fungicide (antifungal).
  • Wide range of colours.
  • Pearl effect.
  • High mechanical performance.
  • Excellent resistance to abrasion.
  • Excellent workability.
  • Extra fine.
  • Easy application.
  • Easy cleaning.


  • Cement-based substrates

Substrate preparation

  • The substrate must be free of damp issues.
  • Clean the seal gap (flanks and bottom) from dust and dirt.
  • The substrates must be clean and sound, free of grease, paint or other substances that would prevent proper adhesion.
  • If the substrate is very porous, it is recommended to apply a protective treatment to the substrate before applying ARJUNT® UNIVERSAL to avoid staining the ceramic tiles.

Instruction for Use

  • Mix ARJUNT® UNIVERSAL with 1.5-1.6 L of clean water per 5 kg bag, or 6.0-6.4 L per 20 kg bag, manually or mechanically for 5 minutes until a homogeneous, creamy, lump-free mixture is obtained.
  • Leave to stand for 5 minutes and stir for a further 5 minutes, reintegrating the material into the container.
  • Fill the joints by compressing the mortar with a spatula or rubber trowel in the direction of the ceramic, spreading the product diagonally or with a spray gun.
  • Wait until the mortar loses its plasticity (the mortar loses its shine) and proceed to clean with a damp sponge or remove the excess of dry mortar with a spatula.
  • Do not carry out this task too early, as it could hollow out the joint or affect the homogeneity of the colour, or too late, as it could damage or modify the surface of the tiles.


  • Before filling the joints, it is necessary to allow 24-48 hours after laying the tiles.
  • Do not apply when there is a risk of frost, rain, strong wind or direct sunlight.
  • Do not apply below 5°C or above 30°C.
  • Do not apply on plaster supports.
  • Do not apply to plastic, metal, wood, rubber, etc. surfaces.

Handling, storage and preservation

  • It is packaged in 20 kg multi-leaf paper bags with damp-proof sheets and in 5 kg plastic bags that allow it to be properly preserved for 12 months in its original closed container, safe from dampness.


  • The information contained in this document and any other advice provided, are given in good faith, based on DANOSA's current knowledge and experience when products are properly stored, handled and applied, in normal situations and in accordance with the recommendations of DANOSA. The information applies only to the application (s) and the product (s) to which reference is expressly made. In case of changes in the parameters of the application, or in case of a different application, consult the DANOSA Technical Service before using the DANOSA products. The information contained herein does not exonerate the responsibility of the building agents to test the products for the application and intended use, as well as their correct application in accordance with current legal regulations. The product images used in our communications are indicative and may differ slightly in color and aesthetic appearance in relation to the final product.Orders are accepted in accordance with the terms of our current General Sales Conditions.DANOSA reserves the right to modify, without prior notice, the data reflected in this documentation.Website: E-mail: Telephone: +34 949 88 82 10


  • Appearance: polvo
  • Colour: Siena

Technical Data

Concept Value Standard
Absorción capilar (kg/m²h0.5) W2 -
Absorción de agua después de 240 min (g) 5 -
Absorción de agua después de 30 min (g) 2 -
Adherencia tras compatibilidad térmica (N/mm²) ≥ 1 -
Adherencia por tracción directa (N/mm²) ≥ 1 -
Agua de amasado (%) 24/26 -
Clasificación según UNE EN 13888 CG2 AW -
Densidad aparente (kg/L) 1,60 ± 0,15 -
Densidad masa fresca (kg/L) 1,60 ± 0,15 -
Intervalo granulométrico (mm) 0/0,3 -
Mass per unit area (nominal) (kg/m²) 5 -
Permeabilidad al vapor de agua (m) Clase I -
Reacción al fuego A1 -
Resistencia a compresión 28 días (N/mm²) ≥ 12 -
Resistencia a compresión 7 días (N/mm²) ≥ 6 -
Resistencia a flexión tras 28 días (N/mm²) ≥ 2,5 -
Abrasion resistance (≤ mm³) ≤ 1000 -
Resistencia a la compresión ciclos (N/mm²) 25 -
Resistencia a la compresión seco (N/mm²) 25 -
Resistencia a la flexotracción ciclos (N/mm²) 6 -
Resistencia a la flexotracción seco (N/mm²) 6 -
Retracción a los 28 días (mm/m) ≤ 3 -
Hazardous substances Ver HS -
Tiempo de vida de la mezcla (min) 60 -


Scroll to Top