DANOCRET PROTECT 200
Mortar for waterproofing concrete structures and capillary network in mortars
Product variations:
EPD S-P-03332
DANOCRET Protect 200 is a polymer modified mortar (PCC), single component for the waterproofing of concrete and mortar structures via the clogging of the capillary network, formulated on the basis of a mixture of hydraulic binders, selected aggregates and hydro-reactive agents that provide excellent adhesion and waterproofing capacity.
Advantages & Benefits
- High protection against saltpetre and seawater according to UNE EN 1504-2.
- Suitable with ARGOCOLA® ELITE 500 C2TES1.
- Good adhesion on non-enamelled substrates (1.1 N/mm², method EN 1542).
- Prevents damp due to condensation.
- Prevents the appearance of efflorescence.
- Great bonding.
- Great elasticity.
- Impervious to water.
- Resistant to freeze/thaw cycles.
Instruction for Use
- Main use: surface dusting in the plastic phase of the concrete or mortar crystallising in the capillary network.
- Mix DANOCRET® Protect 200 with 7.2-7.6 L of clean water per 20 kg bag preferably by mechanical means until a homogeneous, creamy, lump-free mixture with a thick paint consistency is achieved.
- Apply the mortar in two cross coats manually with a stiff nylon brush or suitable spraying systems in thicknesses of approximately 1 mm.
- The application time is 10-20 minutes depending on environmental conditions.
- The second coat should be applied before the first coat has hardened (2-3 hours).
- Protect and dampen the product for at least 48 hours after application to ensure proper material curing.
- On horizontal surfaces and with the mortar or concrete fresh, the product can be applied by sprinkling with an approximate application rate of 1 kg/m².
Presentation
- Weight (kg): 20
- Yield (kg/m²): 3
- Performance in mm thickness (kg/m²): 1,8
- Appearance: Powder
- Colour: Grey
- Product code: 350248
Technical Data
| Concept | Value | Standard |
|---|---|---|
| Mass per unit area (nominal) (kg/m²) | 20 | - |
| Capillary Absorption (kg/m²h0.5) | ≤ 1,00 | EN 1062-3:2008 |
| Adhesion after heat (N/mm²) | ≥ 0,5 | - |
| Initial adhesion (N/mm²) | ≥ 0,5 | - |
| Adhesion after freeze-thaw cycles (N/mm²) | ≥ 0,5 | - |
| Adhesion after thermal compatibility (N/mm²) | ≥ 1,00 | EN 13687-1 y 2 |
| Adhesion after immersion in water (N/mm²) | ≥ 0,5 | - |
| Adhesion after immersion in water with lime (N/mm²) | ≥ 0,5 | - |
| Direct Tensile Adhesion (N/mm²) | ≥ 1,00 | EN 1542:1999 |
| Mixing water (%) | 18/20 | - |
| Crack elongation capacity (mm) | 2.50 (capa de 2 mm a 23 °C) | EN 14891 Apdo. A.8.2 |
| Bulk density (kg/L)v ~ Value | 1,50 ± 0,05 | - |
| Fresh mass density (kg/L) ~ Value | 1,60 ± 0,05 | - |
| Maximum thickness (mm) | 3 | - |
| Minimum thickness (mm) | 2 | - |
| Thickness per layer | Nunca superior a 2 kg/m² | - |
| Water impermeability | cumple | - |
| Grain size range (mm) ~ value | 0/0,8 | - |
| Water vapour permeability (µ) | Clase I | - |
| PH | 10.5 ± 0.5 | - |
| Reaction to fire | A1 | - |
| Compacting resistence 7 days (N/mm²) | 15 | - |
| Resistance to fissure cracking at 0 ºC | A1 | EN 1062-7:2008 |
| Resistence after thermal compatibility (N/mm²) | 1 | - |
| Direct traction resistence (N/mm²) | 1 | - |
| Hazardous substances | Ver HS | - |
Addtitional Technical Data
| Concept | Value | Standard |
|---|---|---|
| Potable water compatibility | no | - |
| CO2 permeability | Clase III | EN 1062-6:2003 |
Agenda cita con un técnico de Danosa
