GLASDAN 40/GP POL
APP plastomeric 4 kg/m² capping sheet. Torch Applied.
Product variations:
ETE 06/0062
GLASDAN 40/GP POL is a waterproofing bituminous sheet with self-protected surface of 4.0 kg/m². Composed of a fibreglass reinforcement, covered on both sides with polymer modified bitumen mastic. On the upper side of the sheet, mineral protection in red colour is used as protective material. The anti-adhesive material used on the lower side is polyethylene film.
Scope
- Self-protected non-accessible roofs: Multilayer waterproofing membrane capsheet with mineral self-protection.
Advantages & Benefits
- The mineral finish gives the membrane UV resistance.
- Plastomer-modified bitumen mastic provides top performance at both high and low temperatures, plasticity and resistance to ageing, leading to increased durability of the sheet and increased safety of the waterproofing membrane.
- Fibreglass felt reinforcement has the following advantages: High dimensional stability, low thermal variation and easy adaptability.
Instruction for Use
Substrate preparation: The base support surface must be durable, uniform, smooth, be clean, dry and free from foreign bodies.
Indications and Important Recommendations
- In case of new construction and renovation, possible chemical incompatibilities with other sheets shall be taken into account.
- In case of refurbishment, chemical incompatibilities with old waterproofing systems consisting of PVC membranes, modified tar-based mastics or any other, shall be taken into account, and it may be necessary to remove them completely or to use suitable separating layers.
- The design and installation of the roof structure and finishes shall be in accordance with the falls prescribed in BS 6229. Ponding of water on the surface of the waterproofing is to be avoided through effective design of roof falls and drainage systems. Throughout the life of the roof, periodic maintenance inspections should be conducted in line with the manufacturer's recommendations.
- This product may form part of a waterproofing system, so all the documents referred to in the Danosa Solutions Manual must be taken into account, as well as all the regulations and legislation that must be complied with in this respect.
- Self-protected sheets finished in light colours perform better thermally.
- Self-protected sheets in coloured mineral or ceramic granules may have different colour shades depending on the different production batches. The mineral granule may darken naturally over time.
- Sheets made of plastomeric bitumen require more blowtorch input than sheets made of SBS elastomeric bitumen in order to work properly. It is important to take this aspect into consideration when welding the sheets to the substrate, when welding the overlaps of the sheets and when welding the sheets to each other.
- There is no chemical incompatibility between the Danosa range of SBS elastomeric bitumen and APP plastomeric bitumen membranes.
- Not to be used in a single-layer waterproofing system.
- Not suitable as cap sheet on green roofs; use GARDEN variant.
- Possible incompatibility between thermal insulation and waterproofing shall be checked.
- Polyurethane foam shall not be sprayed directly on top of the waterproofing without the use of a suitable separating layer (geotextiles, mortar layers, polyethylene film, etc).
Maintenance Recommendations
- Please refer to DANOSA UK Technical Statement ‘Flat Roof Waterproofing – Cleaning and Maintenance Recommendations’
Handling, storage and preservation
- Before moving the pallet, check the condition of the shrink-wrap and reinforce if necessary.
- The product must be stored in a dry place protected from rain, sun, heat and low temperatures.
- The product must be stored in an upright position.
- The product will be used on a first-come, first-served basis.
- This product should not be installed when the temperature is below -5ºC.
- This product is not toxic or flammable.
- NOTE: For more information on the Danosa systems in which this product is used, please see the document "Waterproofing Solutions".
- Waterproofing work must not be carried out when weather conditions may be detrimental, in particular when it is snowing or there is snow or ice on the roof, when it is raining or the roof is wet, surface dampness >8% according to NTE QAT, or when a strong wind is blowing.
- For high storage, the racks must have three cross members, or braces under the wooden pallet skids.
- For handling with a crane, use a protective net.
- Danosa recommends consulting the safety data sheet for this product, which is permanently available at www.danosa.com, Knowlegde Portal, or it can be requested from our Technical Department.
- In all cases, the Occupational Safety and Hygiene standards, as well as the standards of good construction practice, must be taken into account.
Notice
- The information contained in this document and any other advice provided, are given in good faith, based on DANOSA's current knowledge and experience when products are properly stored, handled and applied, in normal situations and in accordance with the recommendations of DANOSA. The information applies only to the application (s) and the product (s) to which reference is expressly made. In case of changes in the parameters of the application, or in case of a different application, consult the DANOSA Technical Service before using the DANOSA products. The information contained herein does not exonerate the responsibility of the building agents to test the products for the application and intended use, as well as their correct application in accordance with current legal regulations. The product images used in our communications are indicative and may differ slightly in color and aesthetic appearance in relation to the final product.Orders are accepted in accordance with the terms of our current General Sales Conditions.DANOSA reserves the right to modify, without prior notice, the data reflected in this documentation.Website: www.danosa.com E-mail: info@danosa.com Telephone: +34 949 88 82 10
Presentation
- Length (cm): 1000
- Width (cm): 100
- Thickness (mm): 2.5(SOLAPO)
- Colour: Grey
- Product code: 141305
Technical Data
| Concept | Value | Standard |
|---|---|---|
| Mass per unit area (nominal) (kg/m²) | 4 | - |
| Density (kg/m³) | 1600 | - |
| External fire behaviour | Broof(t1) | UNE-EN 1187; UNE-EN 13501-5 |
| Durability flexibility | -5 ± 5 | - |
| Creep durability (ºC) | 120 ±10 | UN-EN 1110 |
| Elongation at break longitudinal (%) | NPD | UNE-EN 12311-1 |
| Elongation at transverse break (%) | NPD | UNE-EN 12311-1 |
| Watertightness at 10 kPa (Type A) | Pasa | UNE-EN 1928 |
| Water vapour resistance factor (μ) | 20.000 | UNE-EN 1931 |
| Low temperature flexibility (ºC) | <-15 | UNE-EN 1109 |
| Reaction to fire | E | UNE-EN 11925-2; UNE-EN 13501-1 |
| Resistance to static loading (kg) | NPD | UNE-EN 12730 |
| Resistance to root penetration | No Pasa | EN 13948 |
| Longitudinal tensile strength (N / 5cm) | 550 ± 150 | UNE-EN 12311-1 |
| Transverse tensile strength (N / 5cm) | 400 ± 150 | UNE-EN 12311-1 |
| Longitudinal resistance to tearing (nail shank) (N) | NPD | UNE-EN 12310-1 |
| Transversal resistance to tearing (nail shank) (N) | NPD | UNE-EN 12310-1 |
| Resistance to impact, A (mm) | NPD | UNE-EN 12691 |
| Joint Strength: Welding Shear | NPD | UNE-EN 12317-1 |
| Hazardous substances | PND | - |
Addtitional Technical Data
| Concept | Value | Standard |
|---|---|---|
| Adhesion of granules (%) | <30 | UNE-EN 12039 |
| Dimensional stability at elevated temperatures (longitudinal) (%) | PND | UNE-EN 1107-1 |
| Dimensional stability at high temperatures (transversal) (%) | PND | UNE-EN 1107-1 |
| Creep resistance at high temperatures (ºC) | >130 | UN-EN 1110 |
| UV, heat and water durability: Flexibility at low temperature (ºC) | NPD | - |
| UV, heat and water durability: Flow resistance at elevated temperature (ºC) | NPD | - |
Standards and Certification
- In accordance with the UNE-EN 13707 standard ‘Flexible sheets for waterproofing - Reinforced bitumen sheets for roof waterproofing - Definitions and characteristics’.
- Complies with CE marking requirements.
- Application Document DA18/2009.
- ETE 06/0062 "ESTERDAN Plus FM Bilayer".
- EOTA Guide 006.
Environmental Information
| Concept | Value | Standard |
|---|---|---|
| Volatile organic compounds (COV's) (µg/m³) | 50 (A+) | ISO 16000-6:2006 |
| Post-consumer recycled content (%) | 35 | - |
| Manufactured in | Fontanar - Guadalajara (España) | - |
Agenda cita con un técnico de Danosa
