Danosa > Danosa Global > Products > IMPERDAN FV 2 MM P

IMPERDAN FV 2 MM P

Waterproofing sheet of polymer modified bitumen (pliability -5ºC) with non-protected surface finished with polyethylene film.

Product variations:
Waterproofing
IMPERDAN FV 2 MM P.- (16x1) is a waterproofing bituminous sheet with non self-protected surface, 2.0 mm thickness, LBM-2 mm-FV (APP -5 ºC).Composed of a fibreglass felt reinforcement and covered on both sides with polymer modified bitumen (pliability -5ºC) mastic. A polyethylene film is used as anti-adherent material on both sides. Tested according to standard EN test methods.

Maintenance Recommendations

  • Please refer to DANOSA UK Technical Statement ‘Flat Roof Waterproofing – Cleaning and Maintenance Recommendations’

Handling, storage and preservation

  • Before moving the pallet, check the condition of the shrink-wrap and reinforce if necessary.
  • Consult the product safety datasheet.
  • The product must be stored in a dry place protected from rain, sun, heat and low temperatures.
  • The product must be stored in an upright position.
  • This product is not toxic or flammable.
  • Waterproofing work must not be carried out when weather conditions may be detrimental, in particular when it is snowing or there is snow or ice on the roof, when it is raining or the roof is wet, surface dampness >8% according to NTE QAT, or when a strong wind is blowing.
  • For high storage, the racks must have three cross members, or braces under the wooden pallet skids.
  • For handling with a crane, use a protective net.
  • Membranes will be used on a FIFO basis (First In First Out).
  • In all cases, the Occupational Safety and Hygiene standards, as well as the standards of good construction practice, must be taken into account.

Notice

  • The information contained in this document and any other advice provided, are given in good faith, based on DANOSA's current knowledge and experience when products are properly stored, handled and applied, in normal situations and in accordance with the recommendations of DANOSA. The information applies only to the application (s) and the product (s) to which reference is expressly made. In case of changes in the parameters of the application, or in case of a different application, consult the DANOSA Technical Service before using the DANOSA products. The information contained herein does not exonerate the responsibility of the building agents to test the products for the application and intended use, as well as their correct application in accordance with current legal regulations. The product images used in our communications are indicative and may differ slightly in color and aesthetic appearance in relation to the final product.Orders are accepted in accordance with the terms of our current General Sales Conditions.DANOSA reserves the right to modify, without prior notice, the data reflected in this documentation.Website: www.danosa.com E-mail: info@danosa.com Telephone: +34 949 88 82 10

Presentation

  • Length (cm): 1600
  • Width (cm): 100
  • Thickness (mm): 2.0
  • Product code: 141868
IMPERDAN FV 2 MM P

Technical Data

Concept Value Standard
Durability flexibility +5 ± 5 -
Creep durability (ºC) 120 ±10 UN-EN 1110
Elongation at break longitudinal (%) NPD UNE-EN 12311-1
Elongation at transverse break (%) NPD UNE-EN 12311-1
Watertightness at 10 kPa (Type A) Pasa UNE-EN 1928
Water vapour resistance factor (μ) 20.000 UNE-EN 1931
Low temperature flexibility (ºC) <-5 UNE-EN 1109
Reaction to fire E UNE-EN 11925-2; UNE-EN 13501-1
Resistance to static loading (kg) NPD UNE-EN 12730
Resistance to root penetration No Pasa EN 13948
Longitudinal tensile strength (N / 5cm) 600 ± 200 UNE-EN 12311-1
Transverse tensile strength (N / 5cm) 250 ± 100 UNE-EN 12311-1
Longitudinal resistance to tearing (nail shank) (N) NPD UNE-EN 12310-1
Transversal resistance to tearing (nail shank) (N) NPD UNE-EN 12310-1
Resistance to impact, A (mm) NPD UNE-EN 12691
Joint Strength: Welding Shear NPD UNE-EN 12317-1
Hazardous substances NPD -

Addtitional Technical Data

Concept Value Standard
Adhesion of granules (%) NPD UNE-EN 12039
Dimensional stability at elevated temperatures (longitudinal) (%) NPD UNE-EN 1107-1
Dimensional stability at high temperatures (transversal) (%) NPD UNE-EN 1107-1
Creep resistance at high temperatures (ºC) >130 UN-EN 1110

Standards and Certification

  • In accordance with the UNE-EN 13707 standard ‘Flexible sheets for waterproofing - Reinforced bitumen sheets for roof waterproofing - Definitions and characteristics’.

Environmental Information

Concept Value Standard
Post-consumer recycled content (%) 35 -
Manufactured in Fontanar - Guadalajara (España) -

Downloads