SELF-DAN AL PRO

Self-adhesive SBS elastomeric, easy peel foil faced AVCL.

Product variations:
Waterproofing
BBA 10/4787 (PS1) BBA 10/4787 (PS1)
Self-Adhesive SBS reinforced bitumen Air and Vapor Control Layer (AVCL).
It consists of a self-adhesive low-thickness bituminous compound reinforced by an external aluminium composite film that forms a barrier against vapour and gases. 

  • Upper Surface: Aluminium foil
  • Lower Surface: Removable protective film

Indications and Important Recommendations

  • Exposure to the sun can make it difficult to remove the release film. The temperature of the membrane during installation must not exceed 50ºC.
  • For ease of installation, it is recommended to cut the rolls into smaller, more manageable dimensions.
  • The use of a roller is recommended to apply more pressure on the tape and improve adhesion.
  • It is recommended to protect after installation.

Maintenance Recommendations

  • Please refer to DANOSA UK Technical Statement ‘Flat Roof Waterproofing – Cleaning and Maintenance Recommendations’.

Handling, storage and preservation

  • As this product is not designed for uv-exposed conditions danosa advise that when used as an air and vapour control layer, the product is protected as soon as reasonably possible within a normal sequence of work. However, under normal circumstances and conditions this product may function temporary waterproofing layer for up to 2 weeks. Extreme weather conditionsmay significantly reduce this exposure time. Over-exposed products may require localised repair and/or replacement
  • The product must be stored in a dry place protected from rain, sun, heat and low temperatures.
  • The product must be stored horizontally.
  • This product should not be installed when the ambient, product or support temperature is below +10ºC.
  • Pallets shall not be stacked on top of each other.

Presentation

  • Length (cm): 2000
  • Width (cm): 100
  • Thickness (mm): 1.5
  • Product code: 192120
SELF-DAN AL PRO

Technical Data

Concept Value Standard
External fire behaviour NPD UNE-EN 1187;prUNE-EN 13501-5
Durability flexibility NPD -
Creep durability (ºC) NPD UN-EN 1110
Elongation at break longitudinal (%) 45 ± 15 UNE-EN 12311-1
Elongation at transverse break (%) 45 ± 15 UNE-EN 12311-1
Watertightness at 10 kPa (Type A) Pass EN 1928
Watertightness at 60 kPa (Type A) Pass EN 1928
Water vapour resistance factor (μ) >530000 EN 1931
Low temperature flexibility (ºC) < -25 EN 1109
Reaction to fire F EN 11925-2;EN 13501-1
Resistance to static loading (kg) 5 EN 12730
Resistance to root penetration N/A EN 13984
Longitudinal tensile strength (N / 5cm) 250 ± 100 UNE-EN 12311-1
Transverse tensile strength (N / 5cm) 250 ± 100 UNE-EN 12311-1
Longitudinal resistance to tearing (nail shank) (N) 180 ± 50 EN 12310-1
Transversal resistance to tearing (nail shank) (N) 180 ± 50 EN 12310-1
Resistance to impact, A (mm) 400 EN 12691
Peel strength (N / 50mm) 100 ± 50 EN-12316-1
Joint Strength: Welding Shear 300 ± 100 EN 12317-1
Hazardous substances NPD -
Diffusion equivalent air layer thickness (Sd Value) EN 1931 :2002 (m) >759 -

Addtitional Technical Data

Concept Value Standard
Dimensional stability at elevated temperatures (longitudinal) (%) <2.5 UNE-EN 1107-1
Dimensional stability at high temperatures (transversal) (%) <2.5 UNE-EN 1107-1
Creep resistance at high temperatures (ºC) >70 UN-EN 1110
UV, heat and water durability: Flexibility at low temperature (ºC) NPD -
UV, heat and water durability: Flow resistance at elevated temperature (ºC) NPD -

Environmental Information

Concept Value Standard
Radon diffusion coefficient (m² / s) 1 Exp -13 ISO/DTS 11665-13
Volatile organic compounds (COV's) (µg/m³) 50 (A+) ISO 16000-6:2006
Post-consumer recycled content (%) 35 -
Manufactured in Fontanar - Guadalajara (España) -