POLYDAN 180-40 P ELAST
SBS elastomeric 4 kg/m² underlay. Torch Applied.
Product variations:
BBA 10/4787 (PS1)
EPD S-P-01493
Bituminous SBS modified membrane reinforced with a non-woven polyester felt.
Finished in a quick-melt thermofusible film.
Designed for torch-applied applications and Safe2Torch details using hot-air.
Substrate preparation
- The support must be healthy, clean, flat, free of paint, crumbling or poorly adhered parts, release agents, etc. and in general without any substance or particle that may prevent correct adherence.
Instruction for Use
Where falls apply, membrane rolls should be rolled up the slope so that water drains over and not into membrane overlaps.
Indications and Important Recommendations
- Not suitable as cap sheet on green roofs; use GARDEN variant.
- If expansion that could affect the sheet is expected, a geotextile separating layer (DANOFELT PY 200) shall be used between the sheet and the extruded polystyrene insulation panels, so that each product expands independently.
Maintenance Recommendations
- Please refer to DANOSA UK Technical Statement ‘Flat Roof Waterproofing – Cleaning and Maintenance Recommendations’.
Handling, storage and preservation
- Before moving the pallet, check the condition of the shrink-wrap and reinforce if necessary.
- The product must be stored in a dry place protected from rain, sun, heat and low temperatures.
- The product must be stored in an upright position.
- Pallets shall not be stacked on top of each other.
Presentation
- Length (cm): 1000
- Width (cm): 100
- Thickness (mm): 3.5
- Product code: 141404
Technical Data
| Concept | Value | Standard |
|---|---|---|
| Mass per unit area (nominal) (kg/m²) | 4 | - |
| Density (kg/m³) | 1143 | - |
| External fire behaviour | Broof(t1) | UNE-EN 1187; UNE-EN 13501-5 |
| Durability flexibility | -5 ± 5 | - |
| Creep durability (ºC) | 100 ±10 | UN-EN 1110 |
| Elongation at break longitudinal (%) | 45 ±15 | UNE-EN 12311-1 |
| Elongation at transverse break (%) | 45 ±15 | UNE-EN 12311-1 |
| Watertightness at 10 kPa (Type A) | Pasa | UNE-EN 1928 |
| Watertightness at 60 kPa (Type A) | Pasa | UNE-EN 1928 |
| Water vapour resistance factor (μ) | 20.000 | UNE-EN 1931 |
| Low temperature flexibility (ºC) | <-15 | UNE-EN 1109 |
| Reaction to fire | E | UNE-EN 11925-2; UNE-EN 13501-1 |
| Resistance to static loading (kg) | >20 | UNE-EN 12730 |
| Resistance to root penetration | No Pasa | UNE-EN 13948 |
| Longitudinal tensile strength (N / 5cm) | 900 ± 250 | UNE-EN 12311-1 |
| Transverse tensile strength (N / 5cm) | 650 ± 250 | UNE-EN 12311-1 |
| Longitudinal resistance to tearing (nail shank) (N) | NPD | UNE-EN 12310-1 |
| Transversal resistance to tearing (nail shank) (N) | NPD | UNE-EN 12310-1 |
| Resistance to impact, A (mm) | >1000 | UNE-EN 12691 |
| Resistance to impact, B (mm) | >1500 | - |
| Joint Strength: Welding Shear | 650 ± 250 | UNE-EN 12317-1 |
| Hazardous substances | PND | - |
Addtitional Technical Data
| Concept | Value | Standard |
|---|---|---|
| Adhesion of granules (%) | NPD | UNE-EN 12039 |
| Dimensional stability at elevated temperatures (longitudinal) (%) | <0.5 | UNE-EN 1107-1 |
| Dimensional stability at high temperatures (transversal) (%) | <0.5 | UNE-EN 1107-1 |
| Creep resistance at high temperatures (ºC) | >100 | UN-EN 1110 |
| UV, heat and water durability: Flexibility at low temperature (ºC) | -5 ± 5 | - |
| UV, heat and water durability: Flow resistance at elevated temperature (ºC) | 100 ± 10 | - |
Environmental Information
| Concept | Value | Standard |
|---|---|---|
| Radon diffusion coefficient (m² / s) | 2.4, Exp -12 | ISO/DTS 11665-13 |
| Volatile organic compounds (COV's) (µg/m³) | 50 (A+) | ISO 16000-6:2006 |
| Post-consumer recycled content (%) | 35 | - |
| Manufactured in | Fontanar - Guadalajara (España) | - |