DANOFORCE DARK SIDE
Fast curing hybrid polymer liquid detailing system for bitumen membrane systems.
Product variations:
BBA 20/5743
A highly versatile and flexible fast curing hybrid polymer liquid detailing system for bitumen membrane systems. Can be coated in mineral chippings before curing to match the look of the bituminous cap sheet.
Support
- Reinforced bitumen membranes.
- Asphalt.
Instruction for Use
CATALYST ADDITION:Danoforce dark side is supplied with 50g of danoforce catalyst which must be mixed into the product before application.The danoforce dark side should be mixed with a wooden spatula. Do not mix danoforce dark side with a paddle mixer as this will draw air into the product.
1. Mask of designated area to be coated. It is recommended that the horizontal section extends a minimum of 150mm from the base of the detail to be coated.
2. Apply catalysed danoforce dark side by brush in one overall coat at a minimum coverage of 1.5 litres per m2 (1.8 kg/m²).
3. Check for any thin areas and apply more material as required.
4. Fully blind the liquid with mineral slate chippings until all areas of exposed resin are covered.
5. Remove masking tape and allow to cure.
6. Once the resin has fully cured, gently brush off any excess chippings which may be retained and reused.
7. On completion, seal all terminations with a suitable pu-sealant such as all-weather sealant.
Nb. Danosa uk recommends that where applicable, a small bond-test area is conducted on uncommon, concrete or cement-based structural substrates to ensure suitability of the product for intended purpose.
- On opening: mix thoroughly for at least 30 seconds.
- On addition of catalyst: mix thoroughly until catalyst paste has fully blended. This will take 30-60 seconds.
1. Mask of designated area to be coated. It is recommended that the horizontal section extends a minimum of 150mm from the base of the detail to be coated.
2. Apply catalysed danoforce dark side by brush in one overall coat at a minimum coverage of 1.5 litres per m2 (1.8 kg/m²).
3. Check for any thin areas and apply more material as required.
4. Fully blind the liquid with mineral slate chippings until all areas of exposed resin are covered.
5. Remove masking tape and allow to cure.
6. Once the resin has fully cured, gently brush off any excess chippings which may be retained and reused.
7. On completion, seal all terminations with a suitable pu-sealant such as all-weather sealant.
Nb. Danosa uk recommends that where applicable, a small bond-test area is conducted on uncommon, concrete or cement-based structural substrates to ensure suitability of the product for intended purpose.
Indications and Important Recommendations
- All information on temperature, coverage and timings represent normal working conditions and is provided as a guideline only. However, please contact Danosa UK technical team for advice if you wish to operate outside of these parameters.
Handling, storage and preservation
- When stored unopened in a dry condition, the product shelf life will be indefinite.
Safety and hygiene
- Consult the safety data sheet.
Notice
- The information contained in this document and any other advice provided, are given in good faith, based on DANOSA's current knowledge and experience when products are properly stored, handled and applied, in normal situations and in accordance with the recommendations of DANOSA. The information applies only to the application (s) and the product (s) to which reference is expressly made. In case of changes in the parameters of the application, or in case of a different application, consult the DANOSA Technical Service before using the DANOSA products. The information contained herein does not exonerate the responsibility of the building agents to test the products for the application and intended use, as well as their correct application in accordance with current legal regulations. The product images used in our communications are indicative and may differ slightly in color and aesthetic appearance in relation to the final product.Orders are accepted in accordance with the terms of our current General Sales Conditions.DANOSA reserves the right to modify, without prior notice, the data reflected in this documentation.Website: www.danosa.com E-mail: info@danosa.com Telephone: +34 949 88 82 10
Presentation
- Weight (kg): 2
- Yield (L/m²): 1.50
- Colour: Black
- Product code: 322079
Technical Data
| Concept | Value | Standard |
|---|---|---|
| Cure time at 20 ºC (min) | 30 | - |
Addtitional Technical Data
| Concept | Value | Standard |
|---|---|---|
| Storage time (months) | 6 | - |
| Pot life a 23ºC (min) | 6 Months | - |
Downloads
Product-related solutions
