Danosa > Danosa UK > Contractors > IMPERDAN FP 3 MM AP.

IMPERDAN FP 3 MM AP.

APP plastomeric 3 mm AVCL. Sanded. Torch Applied.

Product variations:
Waterproofing
IMPERDAN FP 3 MM AP is a waterproofing bituminous sheet with sanded finishing, 3 mm thickness. Composed of a non-woven polyester felt reinforcement and covered on both sides with polymer modified bitumen (pliability -5ºC) mastic. Membrane with an upper surface finish of sand and a lower surface finish of polyethylene film. Tested according to standard EN test methods.

Instruction for Use


  • Substrate should be dry and clean from grease, dirt, debris or any other contaminants.
  • Where applicable, prime surface with BITUMEN PRIMER or BITUMEN PRIMER+ in accordance with DANOSA instructions and allow to dry.
  • For field applications:
  • Roll the membrane into position, allowing for 80mm side overlaps and100mm head overlaps and cut to length. All overlaps and cross joints should be staggered by a minimum of 300mm.
  • Using a length of 100mm ø pipe (cut fractionally short of roll width) as an insert tube, roll back the membrane for a portion of the length (approximately 50%).
  • Heat activate the membrane by torching in a vee area between the roll and substrate.
  • Roll can be pushed forward by foot or by other suitable equipment. Apply downwards pressure when moving the roll to extrude a molten bead of bitumen from edges.
  • For detail applications:
  • Place the membrane into position, allowing for 80mm side overlaps and100mm head overlaps and cut to length ensuring all overlaps and cross joints are staggered by a minimum of 300mm.
  • Heat activate the membrane by torching between the membrane and substrate.
  • Apply pressure and consolidate the bond to the substrate, ensuring a molten bead of bitumen is extruded from the edges.


    • Where falls apply, membrane rolls should be rolled up the slope so that water drains over and not into membrane overlaps

    Notice

    • The information contained in this document and any other advice provided, are given in good faith, based on DANOSA's current knowledge and experience when products are properly stored, handled and applied, in normal situations and in accordance with the recommendations of DANOSA. The information applies only to the application (s) and the product (s) to which reference is expressly made. In case of changes in the parameters of the application, or in case of a different application, consult the DANOSA Technical Service before using the DANOSA products. The information contained herein does not exonerate the responsibility of the building agents to test the products for the application and intended use, as well as their correct application in accordance with current legal regulations. The product images used in our communications are indicative and may differ slightly in color and aesthetic appearance in relation to the final product.Orders are accepted in accordance with the terms of our current General Sales Conditions.DANOSA reserves the right to modify, without prior notice, the data reflected in this documentation.Website: www.danosa.com E-mail: info@danosa.com Telephone: +34 949 88 82 10

    Presentation

    • Length (cm): 1000
    • Width (cm): 100
    • Thickness (mm): 3
    • Product code: 141823
    IMPERDAN FP 3 MM AP.

    Technical Data

    Concept Value Standard
    External fire behaviour PND UNE-EN 1187; UNE-EN 13501-5
    Durability flexibility +5 ± 5 -
    Creep durability (ºC) 120 ±10 UN-EN 1110
    Longitudinal traction durability (N / 5cm) 700 ± 200 -
    Transversal tensile durability (N/5cm) 450 ± 150 -
    Elongation at break longitudinal (%) 20 ±15 UNE-EN 12311-1
    Elongation at transverse break (%) 20 ±15 UNE-EN 12311-1
    Watertightness at 10 kPa (Type A) Pasa UNE-EN 1928
    Water vapour resistance factor (μ) 100000 UNE-EN 1931
    Low temperature flexibility (ºC) <-10 UNE-EN 1109
    Reaction to fire E UNE-EN 11925-2; UNE-EN 13501-1
    Resistance to static loading (kg) >15 UNE-EN 12730
    Resistance to static loading (kg) >15 UNE-EN 12730
    Resistance to root penetration No Pasa EN 13948
    Longitudinal resistance to tearing (nail shank) (N) NPD UNE-EN 12310-1
    Transversal resistance to tearing (nail shank) (N) NPD UNE-EN 12310-1
    Resistance to impact, A (mm) >900 UNE-EN 12691
    Joint Strength: Welding Shear 450 ±150 UNE-EN 12317-1
    Resistance to impact, A (mm) >900 UNE-EN 12691
    Joint Strength: Welding Shear 450 ±150 UNE-EN 12317-1
    Hazardous substances NPD -

    Addtitional Technical Data

    Concept Value Standard
    Adhesion of granules (%) NPD UNE-EN 12039
    Dimensional stability at elevated temperatures (longitudinal) (%) <0.6 UNE-EN 1107-1
    Dimensional stability at high temperatures (transversal) (%) <0.6 UNE-EN 1107-1
    Creep resistance at high temperatures (ºC) >130 UN-EN 1110

    Environmental Information

    Concept Value Standard
    Post-consumer recycled content (%) 35 -
    Manufactured in Fontanar - Guadalajara (España) -

    Downloads