SELF DAN PE PLUS.
Reinforced Self-adhesive SBS elastomeric, easy peel 1.5mm membrane.
Product variations:
SELF DAN PE PLUS is a self-adhesive membrane manufactured with bituminous selected mastic modified with high performance SBS polymers, this will provide self-healing properties, easy application and great durability.
As a top layer it has a cross laminated HDPE film, which will provide better mechanical resistance, puncture resistance (static and dynamic), high elongation and high dimensional stability characteristics. At the bottom side it has a releasable film.
Instruction for Use
Surface preparation: _
Alignment:_
Membrane installation: _
Protection system: _
- Concrete must be dry, clean and free from sharp projections such as nail heads and concrete nibs. _
- Remove all surface imperfections, protrusions, cavities, structurally unsound and friable concrete and repair with a suitable repair mortar. _
- Remove contaminants such as grease, oil, dust, dirt, loose stones, debris and wax from exposed concrete. _
- Concrete must be properly dried (minimum 7 days for normal structural concrete and 14 days for lightweight structural concrete). _
- Substrate should be prepared using a primer either IMPRIDAN 100, CURIDAN, MAXDAN or MAXDAN CAUCHO, at the recommended rate (approximately 0,200-0,300 kg/m²) prior to installation of SELF DAN PE PLUS. _
- Primer should be dry before the application of the membrane. Drying time depends of the temperature and humidity. _
Alignment:_
- Start the installation of all membrane plies from the low point or drains, so the flow of water is over or parallel to the plies, but never against the laps. All overlaps at the membrane seams shall be installed so as to have “up” slope laps over “down” slope laps. _
- Begin membrane application by unrolling the roll of SELF DAN PE PLUS membrane and aligning the side laps. Re-roll the roll halfway and hold on the unrolled portion to prevent shifting. _
Membrane installation: _
- Unroll only the required length of SELF DAN PE PLUS and cut the piece to the desired shape and size. _
- Place the pieces of SELF DAN PE PLUS on the area to be covered, and check whether they match with the profile of the marked substrate. _
- Peel off the release film from the self-adhesive side and place the membrane so as to ensure a minimum overlap of 80 mm. _
- Start unrolling the membrane and press it firmly against the surface, from the middle to the edges in order to drive out entrapped air with a wooden press. _
- The surface to be overlapped should be dust free and the membrane must be firmly pressed down to ensure a watertight bond. _
Protection system: _
- In order to prevent damages, SELF DAN PE PLUS must be protected by a protection layer as soon as possible.
Maintenance Recommendations
- Please refer to DANOSA UK Technical Statement ‘Flat Roof Waterproofing – Cleaning and Maintenance Recommendations’
Notice
- The information contained in this document and any other advice provided, are given in good faith, based on DANOSA's current knowledge and experience when products are properly stored, handled and applied, in normal situations and in accordance with the recommendations of DANOSA. The information applies only to the application (s) and the product (s) to which reference is expressly made. In case of changes in the parameters of the application, or in case of a different application, consult the DANOSA Technical Service before using the DANOSA products. The information contained herein does not exonerate the responsibility of the building agents to test the products for the application and intended use, as well as their correct application in accordance with current legal regulations. The product images used in our communications are indicative and may differ slightly in color and aesthetic appearance in relation to the final product.Orders are accepted in accordance with the terms of our current General Sales Conditions.DANOSA reserves the right to modify, without prior notice, the data reflected in this documentation.Website: www.danosa.com E-mail: info@danosa.com Telephone: +34 949 88 82 10
Presentation
- Length (cm): 2000
- Width (cm): 100
- Thickness (mm): 1.5
- Product code: 192235
Technical Data
| Concept | Value | Standard |
|---|---|---|
| External fire behaviour | PND | UNE-EN 1187;prUNE-EN 13501-5 |
| Elongation at break longitudinal (%) | 100 ± 20 | UNE-EN 12311-1 |
| Elongation at transverse break (%) | 100 ± 20 | UNE-EN 12311-1 |
| Watertightness at 10 kPa (Type A) | Pasa | UNE-EN 1928 |
| Water vapour resistance factor (μ) | 115000 | EN 1931 |
| Low temperature flexibility (ºC) | < -15 | UNE-EN 1109 |
| Reaction to fire | F | UNE-EN 11925-2; UNE-EN 13501-1 |
| Resistance to static loading (kg) | 5 | UNE-EN 12730 |
| Resistance to root penetration | No Pasa | EN 13984 |
| Longitudinal tensile strength (N / 5cm) | 200 ± 100 | UNE-EN 12311-1 |
| Transverse tensile strength (N / 5cm) | 200 ± 100 | UNE-EN 12311-1 |
| Longitudinal resistance to tearing (nail shank) (N) | 180 ± 50 | UNE-EN 12310-1 |
| Transversal resistance to tearing (nail shank) (N) | 180 ± 50 | UNE-EN 12310-1 |
| Resistance to impact, A (mm) | 400 | UNE-EN 12691 |
| Joint Strength: Welding Shear | 200 ± 100 | UNE-EN 12317-1 |
| Hazardous substances | PND | - |
Addtitional Technical Data
| Concept | Value | Standard |
|---|---|---|
| Adhesion of granules (%) | PND | UNE-EN 12039 |
| Dimensional stability at elevated temperatures (longitudinal) (%) | <2.5 | UNE-EN 1107-1 |
| Dimensional stability at high temperatures (transversal) (%) | <2.5 | UNE-EN 1107-1 |
| Creep resistance at high temperatures (ºC) | >70 | UN-EN 1110 |
| Dielectric strength (in air, 25 ºC Cl. Nº 12.1.1)~ Value | 9.6 | ASTM D149-09 |
| Volume resistivity (500 V dc – 60 s Cl. Nº 12.2) (Ω·cm) | 6.3 | ASTM D257-14 |
Environmental Information
| Concept | Value | Standard |
|---|---|---|
| Post-consumer recycled content (%) | 35 | - |
| Manufactured in | Fontanar - Guadalajara (España) | - |
