DANODREN GARDEN
HDPE Nodular drainage and geotextile geocomposite for green roofs.
Product variations:
BBA 14/5118 (1)
S-P-01896
DANODREN® JARDIN is a 7.5mm deep green nodular membrane made of high density polyethylene (HDPE) with a pre-bonded non-woven polypropylene geotextile. Its main use is for protection and horizontal drainage.
Advantages & Benefits
- The geotextile fused to the nodules absorbs and filters water from the ground, preventing the system from clogging.
- Easy and quick to install.
- Rot-proof.
- Chemically unchanged when in contact with chemical agents present in the soil (sulphates, chlorides, etc).
- Allows for the transformation of traditionally concrete or asphalt surfaces into green spaces that positively influence the urban microclimate.
- Provides permanent drainage.
- Protects the waterproofing sheet from possible piercing caused by fill earth.
- Resistant to breakage, impact and does not deform.
Instruction for Use
- Intensive green roofs
- The surface of the substrate and singular points must be uniform, clean, dry and free of foreign bodies.
- The substrate for DANODREN Garden is DANOPREN TR extruded polystyrene (XPS), so a geotextile layer of DANOFELT PY 200 polyester must be laid to avoid chemical incompatibility between materials. If the roof is not insulated, the substrate is an asphalt or synthetic waterproofing membrane with root penetration properties.
- DANODREN GARDEN is laid with the geotextile facing upwards.
- The width of the geotextile is 5 cm less than that of the drainage sheet to facilitate the overlapping of roll to roll. To make the overlap, the geotextile is peeled off 7 cm, leaving 12 cm of drainage sheet exposed, where the overlap will be made with the next sheet.
- The topsoil is then spread and placed directly on top of the geotextile layer.
- Construction of a manhole for gardening.
Indications and Important Recommendations
- Store in a dry place, protected from rain, sun, high and low temperatures.
- The product is not toxic or flammable.
- Can´t be used as waterproofing.
Presentation
- Length (cm): 1800
- Width (cm): 210
- Surface (m²): 37.8
- Product code: 314203
Technical Data
| Concept | Value | Standard |
|---|---|---|
| Longitudinal elongation (%) | >40 | - |
| Transverse elongation (%) | 60 ±20 | - |
| Compression strength (kPa) | 250 ±20% | UNE EN ISO 604 |
| Water permeability perpendicular to the plane (m/s) | 0,11 - 0,033 | UNE EN ISO 11058 |
| Dynamic puncture resistance (cone drop test) (mm) | 10 +5 | UNE EN 13433 |
| Longitudinal tensile strength (kN/m) | 19, -4 | UNE EN ISO 10319 |
| Tranversal tensile strength (kN/m) | 15, -4 | UNE EN ISO 10319 |
| Hazardous substances | NPD | - |
| Characteristic aperture size (µm) | 87,5 +/- 42,5 | UNE EN ISO 12956 |
Addtitional Technical Data
Standards and Certification
- CTE DB-HE: Technical Building Code. Basic Document: Habitability. Energy saving
- Conforms to the UNE-EN 13252 standard for Geotextiles and related products. Characteristics required for use in drainage systems.
- Conforms to UNE-EN 13967 of plastic and rubber anti-capillary sheets, including plastic and rubber sheets used for sealing buried structures.
- DIT 550R/16 "ESTERDAN PENDIENTE ZERO".
- DIT 550R/20 "DANOPOL PENDIENTE ZERO"
- BUREAU VERITAS company registration according to EN-ISO 14001 granted to DANOSA's manufacturing plant in Fontanar (Guadalajara).
- BUREAU VERITAS company registration according to EN-ISO 9001 granted to DANOSA's manufacturing plant in Fontanar (Guadalajara).
- EU Regulation 305/2011. Construction products.
Environmental Information
| Concept | Value | Standard |
|---|---|---|
| Volatile organic compounds (COV's) (µg/m³) | NPD | - |
| Post-consumer recycled content (%) | 80 | - |
| Pre-Consumer recycled content (%) | 20 | - |
| Solar reflectance index (SRI) | NPD | - |
| Manufactured in | Fontanar - Guadalajara (España) | - |
Agenda cita con un técnico de Danosa
