DANOPUR LT GREY
Polyurethane liquid membrane for finishing of waterproofing systems with DANOPUR HT with heavy traffic.
Product variations:
DANOPUR® LT Grey is a one-component, aliphatic, UV stable, semi-rigid, high abrasion resistant, one-component polyurethane sealer and topcoat, suitable for foot and road traffic, used as a final sealer and topcoat for DANOPUR and DANOCOAT systems.
Instruction for Use
- Application method: Top-coat with DANOPUR® PARKING or DANOCOAT® PARKING system. Apply two coats uniformly by roller or airless, in case of airless application always go over with a short nap roller. Allow to dry for 4 to 6 hours (never more than 8 hours) between coats. Attention: DANOPUR® LT should only be used as a topcoat for DANOPUR® HT and DANOFLOOR® PU300 that has been dusted with silica (0,3-0,8mm).
- Total consumption: The recommended total consumption is 400 to 600 g/m² applied in thin coats and will depend on the end use of the application. It may also vary according to the porosity or irregularity of the surface, as well as environmental conditions.
- Tools: Roller, brush, or airless spraying equipment.
- Checking environmental conditions: Ambient temperature between 5 to 35ºC. Relative humidity < 80%. The ambient temperature has a direct influence on the curing times. At lower temperatures the curing will take longer and at higher temperatures the product will cure faster. If the humidity is higher than recommended, the final finish may be altered.
- Product preparation and application: With the help of a mechanical stirrer obtain a homogeneous mixture. DANOPUR® LT GREY should be applied over DANOPUR® aromatic waterproofing membranes, cured and saturated with DANOQUARTZ® SP 49 aggregate or similar to promote mechanical anchoring of the membrane. Saturating the last layer of DANOPUR® waterproofing membrane creates a surface that is more resistant to wear and abrasion. The second coat of DANOPUR® LT GREY should be applied 5 to 6 hours after the first coat and never more than 36 hours. A third coat may be applied depending on the end use of the surface. DANOPUR® LT GREY is slippery if wet. To avoid this, it is recommended to sprinkle DANOQUARTZ SP49 silica aggregate in the last coat of the system to achieve a slip resistant surface. DANOPUR® LT GRIS is not recommended for use in direct contact with treated or chlorinated water. If there are areas of water stagnation on the application surface, they should be cleaned regularly to avoid biological and microbial attack.
Warning
- Clean all tools and spraying equipment with cleaning diluent immediately after use.
Cleaning of Work Tools
Clean all tools and spraying equipment with cleaning diluent immediately after use.
Presentation
- Weight (kg): 10
- Yield (kg/m²): 0.2 - 0.6
- Colour: Grey
- Product code: 750706
Technical Data
| Concept | Value | Standard |
|---|---|---|
| Degradación de la superficie después de 2000h de envejecimiento acelerado | Grado 0 | DIN EN ISO 46286-6 |
| Elongation at break (%) | > 100 | ASTM D412 |
| Envejecimiento acelerado UV en presencia de humedad | Superado | - |
| Tensile strength (N/mm²) | > 5 | ASTM D412 |
| Temperatura de servicio (ºC) | -30 a + 90 | - |
| Tiempos de secado (23ºC y 50% HR). Curado total (días) | 7 | - |
| Drying times (23ºC and 50% RH). Final drying time (days) | 7 | - |
| Tiempos de secado (23ºC y 50% HR). Tiempo para tránsito de personas (horas) | 12 | - |
| Hardness (Shore A) | 30 | ASTM D2240 |
Addtitional Technical Data
Downloads
Agenda cita con un técnico de Danosa
