DANOPOL HS 1.5
Single Ply PVC-p 1.5 mm membrane. Mechanically Fixed.
Product variations:
BBA 14/5118 (1)
EPD S-P-00691
ETE 10/0054
FM Approvals PR455736 RR242640
DANOPOL HS 1.5 is a synthetic PVC plasticized membrane, Reinforced with polyester net carrier. Designed for flat roof waterproofing, U.V. resistant.
Scope
- Channel waterproofing (EN 13362).
- Mechanically fastened roof waterproofing systems (EN 13956).
- Waterproofing of reservoirs and dams (EN 13361).
- Waterproofing against fluids in the construction of tunnels and underground structures (EN 13491).
Advantages & Benefits
- Good absorption of structural movements.
- High tensile strength.
- High resistance to piercing.
- Hot air welded: Flame-free system
- Great elasticity.
- High resistance to tearing.
- Allows for adaptation to any type of geometry.
- UV resistant.
- System with Environmental Product Declaration (EPD), type 3 ecolabel.
- System fixed by metallic, plastic or induction fixation.
Support
- Deck-type metal roof.
- Overlays*
- Insulation panels.*
- Concrete subsrates.
- Wooden subsrates.
- Mortar subsrates.
Handling, storage and preservation
- The product must be stored in a dry place protected from rain, sun, heat and low temperatures.
- The product will be used on a first-come, first-served basis.
- This product is not toxic or flammable.
- Easy to cut to adapt the dimensions to the work.
- Waterproofing work must not be carried out when weather conditions may be detrimental, in particular when it is snowing or there is snow or ice on the roof, when it is raining or the roof is wet, surface dampness >8% according to NTE QAT, or when a strong wind is blowing.
- No welding work should be carried out when the ambient temperature is lower than -5ºC for hot air welding, nor lower than + 5ºC for welding with THF or with Adhesives.
- It shall be kept in its original packaging, in a horizontal position and all rolls parallel (never crossed), on a flat and smooth support.
- Danosa recommends consulting the safety data sheet for this product, which is permanently available at danosa.com, Knowlegde Portal, or it can be requested from our Technical Department.
- In all cases, the Occupational Safety and Hygiene standards, as well as the standards of good construction practice, must be taken into account.
- For further information, please contact our Technical Department.
Notice
- The information contained in this document and any other advice provided, are given in good faith, based on DANOSA's current knowledge and experience when products are properly stored, handled and applied, in normal situations and in accordance with the recommendations of DANOSA. The information applies only to the application (s) and the product (s) to which reference is expressly made. In case of changes in the parameters of the application, or in case of a different application, consult the DANOSA Technical Service before using the DANOSA products. The information contained herein does not exonerate the responsibility of the building agents to test the products for the application and intended use, as well as their correct application in accordance with current legal regulations. The product images used in our communications are indicative and may differ slightly in color and aesthetic appearance in relation to the final product.Orders are accepted in accordance with the terms of our current General Sales Conditions.DANOSA reserves the right to modify, without prior notice, the data reflected in this documentation.Website: www.danosa.com E-mail: info@danosa.com Telephone: +34 949 88 82 10
Presentation
- Length (cm): 1500
- Length measurement standard: EN 1848-2
- Width (cm): 180
- Width measurement standard: EN 1848-2
- Colour: White
- Thickness (mm): 1.5
- Product code: 210053
Technical Data
Concept | Value | Standard |
---|---|---|
Mass per unit area (nominal) (kg/m²) | 1.9 | - |
Longitudinal elongation at break (%) | > 100 | - |
Transversal elongation at break (%) | > 110 | - |
External fire behaviour | Broof (t1) - Broof (t3) - Broof (t4) | EN 13501-5 |
Longitudinal & transversal dimensional stability | < 0.3 | EN 1107-2 |
Water vapour permeability (m) | 47.000 ± 30% | EN 1931 |
Flexibility at low temperature (ºC) | < -30 | EN 495-5 |
Reaction to fire | E | EN 13501-1 |
Resistance to static loading (kg) | > 55 | - |
Resistance to static loading; method B (hard support) (kg) | > 55 | EN 12730 Método B |
Resistance to root penetration | Pasa | EN 13948 |
Longitudinal & transversal tensile strength (N/5cm) | > 1100 / 1000 | EN 12311-2 Método A |
Longitudinal resistance to tearing (nail shank) (N) | > 250 | EN 12310-2 |
Transversal resistance to tearing (nail shank) (N) | > 250 | EN 12310-2 |
Resistance to impact, A (mm) | > 700 | EN 12691 |
Overlaps resistance (Shear of overlaps) (N/50mm) | > 950 | EN 12317-2 |
Overlaps resistance (Peeling of overlap) (N/50mm) | > 250 | EN 12316-2 |
Hazardous substances | PND | - |
Addtitional Technical Data
Concept | Value | Standard |
---|---|---|
Visible defects | Pasa | EN 1850-2 |
Nominal minimum thickness | 1.5 (-5%; +10%) | EN 1849-2 |
Mass (kg/m²) | 1.9 (-5%; +10%) | EN 1849-2 |
Loss of elongation at break (UV 5000 h) | < 10< 10 | EN 1297, EN 12311-2EN 1297, EN 12311-2 |
Loss of plasticizers (mass change at 30 days) (%) | < 4.5 | EN ISO 177 |
Flatness (mm) | < 10 | EN 1848-2 |
Straightness (mm) | < 50 | EN 1848-2 |
Resistance to static punching (N) | > 1200 | UNE 104416 (b) |
Environmental Information
Concept | Value | Standard |
---|---|---|
Post-consumer recycled content (%) | NDP | - |
Pre-Consumer recycled content (%) | NDP | - |
Solar reflectance index (SRI) | 103 | ASTM E1980-11 |
Manufactured in | Fontanar - Guadalajara (España) | - |