ESTERDAN PLUS 40/GP ELAST

SBS elastomeric 4 kg/m² capping sheet. Torch Applied.

Product variations:

BBA 10/4787 (1)

EPD S-P-01493

ETE 06/0062

Datasheet

Commercial Sheet

Declaration of Performance (DoP)

Description Technical features and measures Related documentation

Bituminous SBS modified capsheet reinforced with a non-woven polyester felt. The upper surface is finished with mineral chippings. The underside has a quick-melt thermofusible film. Designed for torch-applied applications and Safe2Torch details using hot-air.

Scope

Anti-capillary barrier in walls.
Capsheet for double layer waterproofing systems.
Top sheet in two-layer membranes for waterproofing of roofs with heavy bonded, unbonded or floating protection.

Advantages & Benefits

High static and dynamic piercing resistance.
Self-healing and Rot-proof.
The mineral finish gives the membrane UV resistance.
High tensile strength and high elongation at break.
High resistance to tearing.
Total impermeability to water and water vapour.
Very stable in the long term.
Allows for adaptation to any type of geometry.

Support

Roofs with heavy bonded, unbonded or floating and self-protected bonded protection.
Compatible thermal insulation.
Concrete supports
Mortar supports

Instruction for Use

Preparation of the substrate:

The surface of the base substrate shall be resistant, uniform, smooth, clean, dry and free of foreign bodies. In the case of thermal insulation, the boards shall be laid in a grid and without gaps of more than 0.5 cm between boards.

Top layer of multi-layer membranes with mineral self-protection. The sheet is laid in the same direction as the bottom sheet, with the overlap line offset by approximately half of the roll. The sheet is fully welded to the bottom sheet with a blowtorch. The overlaps are to be welded, and will be 8 cm in both the longitudinal and transverse directions. To join the transverse overlap at the ends of the rolls, it is necessary to heat the transverse edge of the lower sheet in a strip of 8-10 cm beforehand, removing or embedding the protective aggregate in the bituminous mass and then welding the end of the next piece.
Waterproofing under tiles on pitched roofs. The adhesion of the sheet to the substrate is done with a blowtorch. In the case of mortar or concrete substrates, a bituminous primer (Curidán, Impridán 100, Maxdán or Maxdán Caucho) must be applied beforehand. If the substrate is a weldable thermal insulation board, i.e. asphalt-finished (Rocdán A or Rocdán PIR VA), the primer is not necessary. The overlaps are to be welded, and shall be 8 cm in both longitudinal and transverse directions. To join the transversal overlap at the ends of the rolls, it is necessary to previously heat the transversal edge of the lower sheet in a strip of 8-10 cm, eliminating or embedding the protection aggregate in the bituminous mass and then weld the end of the following piece. The mechanical fastening is carried out at the overlaps.

Indications and Important Recommendations

In case of new construction and renovation, possible chemical incompatibilities with APP plastomer-modified bitumen sheets shall be taken into account.
In case of renovation, chemical incompatibilities with old waterproofing consisting of flexible PVC sheets, modified tar-based mastics or any other, shall be taken into account, and it may be necessary to remove them completely or to use suitable separating layers (geotextiles, mortar layer, polyethylene film, etc).
If it is necessary to adhere to metallic or slightly porous elements, a bituminous primer (IMPRIDAN 100) shall be applied to the entire surface to be welded beforehand.
On exposed self-protected roofs, occasional water retention that could lead to sediment accumulation and damage to the waterproofing membrane shall be avoided.
This product is part of a waterproofing system, so all the documents referred to in the Danosa Solutions Manual must be taken into account, as well as all the regulations and legislation that must be complied with in this respect.
Self-protected sheets finished in light colours perform better thermally.
Self-protected sheets in coloured mineral or ceramic granules may have different colour shades depending on the different production batches. The mineral granule may darken naturally over time.
Self-protected sheets are exposed sheets, so care must be taken when installing them.
NOTE: For more information on the Danosa systems in which this product is used, please see the document "Waterproofing Solutions".
There is no chemical incompatibility between the Danosa range of oxyasphalt, SBS elastomeric bitumen and plastomeric bitumen sheets.
Do not use as a top sheet on green roofs.
Do not use as a single-ply membrane, except for waterproofing under tiles on pitched roofs.
Possible incompatibility between thermal insulation and waterproofing shall be checked.
Special attention must be paid to the execution of the singular points, such as parapets (meetings with vertical and emergent elements), drains, expansion joints, etc.
Polyurethane foam shall not be sprayed directly on top of the waterproofing without the use of a suitable separating layer (geotextiles, mortar layers, polyethylene film, etc).
If expansion that could affect the sheet is expected, a geotextile separating layer (Danofelt PY 200) shall be used between the sheet and the extruded polystyrene insulation panels, so that each product expands independently.

Maintenance Recommendations

The following maintenance checks must be adhered to: - A general examination on the condition of the waterproofing and surrounding roof components. - An inspection of all functional roofing elements including skylights, outlets, upstands, penetrations and any other visible roofing components. - Clean outlets, drains, gutters and remove any debris from the roof. - Periodic removal of mildew, moss, herbs or any other kind of vegetation that has been accumulation on the waterproofing. - Periodic removal of possible sediments accumulated on the deck (silt, sledges, slate granules, etc) by occasional water accumulation. - Periodic removal of debris and small objects that may have accumulated on the roof. - Ensure surrounding structural elements are sound such as eaves, flashings, slate tiles and brickwork. - Ensure that the waterproofing is in good condition and there are no blisters, damage or separation. - Review the condition of the waterproofing (adherence to upstands, condition of overlaps, visual appearance, etc) and repair the defects observed. These operations must be carried out twice a year, preferably at the beginning of spring or autumn and must be increased in case of decks or valleys with zero falls. It is also necessary to perform additional maintenance depending on the type of roof, location and proximity of roofs to areas with trees or in areas with high levels of pollution. Speak to our Technical Team for further information.

Warning

Do not apply on wet or frozen surfaces.

Handling, storage and preservation

Before moving the pallet, the condition of the shrink-wrap is checked in order to reinforce it if necessary.
The product must be stored in a dry place protected from rain, sun, heat and low temperatures.
The product will be stored in an upright position.
Handle with a crane with a protective net.
Pallets shall not be stacked on top of each other.

Notice

The information contained in this document and any other advice provided, are given in good faith, based on DANOSA's current knowledge and experience when products are properly stored, handled and applied, in normal situations and in accordance with the recommendations of DANOSA. The information applies only to the application (s) and the product (s) to which reference is expressly made. In case of changes in the parameters of the application, or in case of a different application, consult the DANOSA Technical Service before using the DANOSA products. The information contained herein does not exonerate the responsibility of the building agents to test the products for the application and intended use, as well as their correct application in accordance with current legal regulations. The product images used in our communications are indicative and may differ slightly in color and aesthetic appearance in relation to the final product.Orders are accepted in accordance with the terms of our current General Sales Conditions.DANOSA reserves the right to modify, without prior notice, the data reflected in this documentation.Website: www.danosa.com E-mail: info@danosa.com Telephone: +34 949 88 82 10

Presentation

Length (cm): 600
Width (cm): 100
Thickness (mm): 2.5 (SOLAPO)
Product code: 141397

Technical Data

Concept	Value	Standard
External fire behaviour	Broof(t1)	UNE-EN 1187
Durability flexibility	-5 ± 5	-
Creep durability (ºC)	100 ±10	UN-EN 1110
Elongation at break longitudinal (%)	45 ±15	UNE-EN 12311-1
Elongation at transverse break (%)	45 ±15	UNE-EN 12311-1
Humidity resistance factor	20.000	UNE-EN 1931
Low temperature flexibility (ºC)	<-15	UNE-EN 1109
Mass per unit area (nominal) (kg/m²)	4	-
Reaction to fire	E	UNE-EN 11925-2; UNE-EN 13501-1
Resistance to static loading (kg)	>15	UNE-EN 12730
Resistance to root penetration	No pasa	UNE-EN 13948
Longitudinal tensile strength (N / 5cm)	700 ± 200	-
Transverse tensile strength (N / 5cm)	450 ± 150	-
Longitudinal resistance to tearing (nail shank) (N)	PND	-
Transversal resistance to tearing (nail shank) (N)	PND	-
Hazardous substances	PND	-

Addtitional Technical Data

Concept	Value	Standard
Adhesion of granules (%)	<30	UNE-EN 12039
Dimensional stability at elevated temperatures (longitudinal) (%)	<0.3	UNE-EN 1107-1
Dimensional stability at high temperatures (transversal) (%)	<0.3	-
Creep resistance at high temperatures (ºC)	>100	UN-EN 1110

Standards and Certification

BBA 10/4787 Product Sheet 1 "GLASDAN ELAST, ESTERDAN ELAST AND POLYDAN ELAST ROOF WATERPROOFING MEMBRANES".
In accordance with the UNE-EN 13707 standard for flexible sheets for waterproofing. Reinforced bituminous sheets for roof waterproofing. Definitions and characteristics.
In accordance with the UNE-EN 13969 standard for flexible sheets for waterproofing. Bituminous anti-capillary sheets including bituminous sheet for sealing buried structures. Definitions and characteristics.
It complies with the requirements of the Technical Building Code (CTE).
Complies with CE marking requirements.
DTA 5/09-2088 "Glasdan ELAST-Esterdan ELAST-Polydan ELAST".
Application Document DA39/2013.
ETE 06/0062 "Esterdan Plus FM Bilayer".