M.A.D. 4 AUTOADHESIVE
4mm Self-Adhesive bituminous membrane for low frequency acoustic insulation.
Product variations:
EPD S-P-01923
Membrana Acústica Danosa M.A.D.4 autoadhesiva (placas) is a high density membrane of bitumen modified self-adhesive specifically designed to behave as an anti resonant material.rIt is an efficient substitute for lead sheets
Instruction for Use
Preliminary operations
Following the instructions and recommendations of the plasterboard manufacturers, the profiles should be fixed to the substrate including sealing strips.
On the ceiling, the mechanical strength of the damper and profile system must first be checked.
The first plasterboard is then fixed to the supporting structure with a sheet metal screw.
Make sure that this board is dry, clean and free of foreign bodies.
Laying of Danosa M.A.D.6 self-adhesive Acoustic Membrane:
1. On the wall
Start by cutting complete pieces of Danosa Acoustic Membrane M.A.D.6 self-adhesive to the same size as the height of the partition wall. The remnants will be used in the smaller panels or for finishing.
The anti-adhesive film is removed from the top of the piece.
Once the piece has been placed square to the facing, the membrane is pressed tightly against the laminated plaster, avoiding any wrinkles.
In the same way, the anti-adherent film is removed while the membrane is pressed to the plasterboard until the cut piece is completed.
To maintain the continuity of the membrane, the MAD has a recess at the edges that must be matched.
The second plasterboard is screwed to the supporting structure with sheet metal screws.
It is important to butt the joints with the first board, to avoid loss of watertightness.
2. Ceiling
Start by cutting pieces of self-adhesive Danosa Acoustic Membrane M.A.D.6 transversally to the roll at a distance of 1.2m. This produces pieces of 1 x 1.2 m2. The remnants will be used in the smaller panels or for finishing.
It can be applied with a mechanical fixing system or with gluing systems following the steps described in the wall application method.
It is possible to work directly on the ceiling by fixing the membrane to the first plasterboard or, on the other hand, to work on the floor by applying the membrane to the second board.
In the latter case, after fixing the membrane with staples or glue, the membrane and the second board are lifted by means of a mechanical lift.
This assembly is then screwed to the primary-secondary roof structure with sheet metal screws.
It is important to butt the joints with the first plate to avoid leakage.
Note: DPS: Sound Insulation Installation Manual. Details of Singular Points.
Following the instructions and recommendations of the plasterboard manufacturers, the profiles should be fixed to the substrate including sealing strips.
On the ceiling, the mechanical strength of the damper and profile system must first be checked.
The first plasterboard is then fixed to the supporting structure with a sheet metal screw.
Make sure that this board is dry, clean and free of foreign bodies.
Laying of Danosa M.A.D.6 self-adhesive Acoustic Membrane:
1. On the wall
Start by cutting complete pieces of Danosa Acoustic Membrane M.A.D.6 self-adhesive to the same size as the height of the partition wall. The remnants will be used in the smaller panels or for finishing.
The anti-adhesive film is removed from the top of the piece.
Once the piece has been placed square to the facing, the membrane is pressed tightly against the laminated plaster, avoiding any wrinkles.
In the same way, the anti-adherent film is removed while the membrane is pressed to the plasterboard until the cut piece is completed.
To maintain the continuity of the membrane, the MAD has a recess at the edges that must be matched.
The second plasterboard is screwed to the supporting structure with sheet metal screws.
It is important to butt the joints with the first board, to avoid loss of watertightness.
2. Ceiling
Start by cutting pieces of self-adhesive Danosa Acoustic Membrane M.A.D.6 transversally to the roll at a distance of 1.2m. This produces pieces of 1 x 1.2 m2. The remnants will be used in the smaller panels or for finishing.
It can be applied with a mechanical fixing system or with gluing systems following the steps described in the wall application method.
It is possible to work directly on the ceiling by fixing the membrane to the first plasterboard or, on the other hand, to work on the floor by applying the membrane to the second board.
In the latter case, after fixing the membrane with staples or glue, the membrane and the second board are lifted by means of a mechanical lift.
This assembly is then screwed to the primary-secondary roof structure with sheet metal screws.
It is important to butt the joints with the first plate to avoid leakage.
Note: DPS: Sound Insulation Installation Manual. Details of Singular Points.
Presentation
- Length (cm): 600
- Width (cm): 100
- Thickness (mm): 4.0
- Surface (m²): 6
- Product code: 610036
Technical Data
| Concept | Value | Standard |
|---|---|---|
| Mass per unit area (nominal) (kg/m²) | 6 | - |
| Improvement to airborne noise on laminated gypsum board partition, ΔR (dBA) | 4 | EN 140-16 |
| Improved insulation at 125 Hz (between elements resort) (dB) | 9.5 | EN 140-16 |
| Insulation improvement at 125 Hz (between rigid elements) (dB) | 6 | EN 140-16 |
| Tolerance (%) | <10 | EN 1849-1 |
| Poisson coefficient | 0.48 | - |
| Watertightness at 10 kPa (Type A) | Pasa | UNE-EN 1928 |
| Young's module (kPa) | 70 | EN 527-2 |
| Reaction to fire | C s3 d0 | EN 13501-1 |
| Resistance to tearing (nail shank) (N) | 180 ± 50 | EN 12310-1 |
Addtitional Technical Data
| Laboratory | Test (EN 140-3) No | Result (EN 717-1) |
|---|---|---|
| L.G.A.I. | 97.017.996 | RA = 33,2 dBA |
| L.G.A.I. | 98.012.316 | RA = 47,2 dBA |
| L.G.A.I. | 98.012.317 | RA = 54,3 dBA |
| L.G.A.I. | 98.012.318 | RA = 65,8 dBA |
| LABEIN | B130-134-H91 | RA = 64,2 dBA |
| LABEIN | B130-134-H94 | RA = 65,4 dBA |
| DANOSA | 95/MAD/008 | RA = 38,5 dBA |
Environmental Information
| Concept | Value | Standard |
|---|---|---|
| Volatile organic compounds (COV's) (µg/m³) | 50 | ISO 16000-6:2006 |
| Content of recycled raw material (%) | 15 | - |
| Post-consumer recycled content (%) | 60 | - |
| Pre-Consumer recycled content (%) | - | - |
| Manufactured in | Fontanar - Guadalajara (España) | - |
Agenda cita con un técnico de Danosa
